Chief Manufacturing MP3 Player Accessories SMA 602 User Manual

I N S T A L L A T I O N I N S T R U C T I O N S  
Pipe Adapter for SL-151 Projector Lift  
Spanish Product Description  
German Product Description  
Portuguese Product Description  
Italian Product Description  
Dutch Product Description  
French Product Description  
SMA-602  
 
Installation Instructions  
SMA-602  
LEGEND  
Tighten Fastener  
Pencil Mark  
Apretar elemento de fijación  
Befestigungsteil festziehen  
Apertar fixador  
Marcar con lápiz  
Stiftmarkierung  
Marcar com lápis  
Segno a matita  
Potloodmerkteken  
Marquage au crayon  
Serrare il fissaggio  
Bevestiging vastdraaien  
Serrez les fixations  
Loosen Fastener  
Drill Hole  
Aflojar elemento de fijación  
Befestigungsteil lösen  
Desapertar fixador  
Perforar  
Bohrloch  
Fazer furo  
Praticare un foro  
Gat boren  
Allentare il fissaggio  
Bevestiging losdraaien  
Desserrez les fixations  
Percez un trou  
Phillips Screwdriver  
Adjust  
Destornillador Phillips  
Ajustar  
Kreuzschlitzschraubendreher  
Chave de fendas Phillips  
Cacciavite a stella  
Einstellen  
Ajustar  
Regolare  
Afstellen  
Ajuster  
Kruiskopschroevendraaier  
Tournevis à pointe cruciforme  
Open-Ended Wrench  
Llave de boca  
Remove  
Quitar  
Gabelschlüssel  
Chave de bocas  
Chiave a punte aperte  
Steeksleutel  
Entfernen  
Remover  
Rimuovere  
Verwijderen  
Retirez  
Clé à fourche  
By Hand  
Optional  
Opcional  
Optional  
Opcional  
Opzionale  
Optie  
A mano  
Von Hand  
Com a mão  
A mano  
Met de hand  
À la main  
En option  
Hex-Head Wrench  
Security Wrench  
Llave de cabeza hexagonal  
Sechskantschlüssel  
Chave de cabeça sextavada  
Chiave esagonale  
Llave de seguridad  
Sicherheitsschlüssel  
Chave de segurança  
Chiave di sicurezza  
Veiligheidssleutel  
Clé de sécurité  
Zeskantsleutel  
Clé à tête hexagonale  
3
 
SMA-602  
Installation Instructions  
TOOLS REQUIRED FOR INSTALLATION  
#2  
1/2" (12.7mm)  
9/16" (14.3mm)  
5/32"(included)  
PARTS  
B (1)  
5/16-18 x 1/4"  
C (3)  
3/8-16 x 3 1/2"  
A (1)  
[Pipe adapter]  
F (1)  
5/32"  
D (12)  
3/8-16"  
E (12)  
3/8"  
4
 
Installation Instructions  
SMA-602  
Assembly And Installation  
The SMA-602 pipe adapter assembly was designed to attach  
the UL-Listed SL151 lift (not included) to a 1-1/2" NPT or NPSM  
following ANSI/ASME B1.20.1 (Schedule 40, 0.154" minimum  
thickness steel or aluminum - ASTM B221) threaded extension  
column (not included). A minimum of four threads must be  
engaged.  
(C) x 3  
1
(underside of SL-151)  
(E) x 3  
Disassemble Pipe Adapter Assembly  
1. Unscrew four hex nuts on pipe adapter assembly (A). (See  
Figure 1)  
2. Remove top and bottom slide assembly plates from main  
plate. (See Figure 1)  
hex nuts x 4  
1
top slide plate  
main plate  
Figure 2  
(D) x 3  
(E) x 3  
2
bottom slide plate  
(underneath)  
Figure 3  
(D) x 3  
4
Figure 1  
Attach Main Plate to SL-151 Lift  
1. Insert a 3/8-16 x 3 1/2" hex head tap bolt (C) through a 3/8"  
washer (E) and through one of three holes on top of SL-151  
lift. (See Figure 2)  
2. Install a 3/8" washer (E) and a 3/8-16" hex nut (D) over tap  
bolt. (See Figure 3)  
3. Repeat Steps 1-2 for other two holes on SL-151 lift.  
4. Thread each nut completely on bolts. (See Figure 4)  
Figure 4  
5
 
SMA-602  
Installation Instructions  
5. Partially thread a 3/8-16" hex nut (D) onto each of three 3/  
8-16 x 3 1/2" hex head tap bolts (C). (See Figure 5)  
Attaching Main Plate and SL-151 to Ceiling Pipe  
IMPORTANT ! : Only attach SMA-602 to UL Listed Chief  
ceiling mount SL151.  
6. Place a 3/8" washer (E) over each hex nut. (See Figure 5)  
IMPORTANT ! : These installation instructions assume that a  
1-1/2" NPT or NPSM following ANSI/ASME B1.20.1 (Schedule  
40, 0.154" minimum thickness aluminum - ASTM B221)  
threaded extension column (not included) has been properly  
installed and is in place.  
7. Place main plate over three bolts lining up the holes on the  
outside edge of the plate with the screws. (See Figure 5)  
8. Place another 3/8" washer (E) and 3/8-16" hex nut (D) over  
each bolt. (See Figure 5)  
1. Thread top slide plate assembly onto ceiling pipe until it  
cannot be tightened any further. (See Figure 7)  
main plate  
2. Adjust top slide plate assembly back clockwise until set  
screw hole is facing target. (See Figure 7)  
(D) x 3  
(E) x 3  
8
(D) x 3  
5
(E) x 3  
IMPORTANT ! : When SMA-602 is properly positioned, the  
set screw access hole should be pointing directly at target.  
3. Insert 5/16-18 x 1/4" set screw (B) into access hole to  
secure top slide plate to ceiling pipe. (See Figure 7)  
ceiling pipe  
1
top slide plate  
assembly  
2
Figure 5  
(B)  
3
9. Secure main plate near top of bolts by threading nuts  
together. Make sure to leave plenty of space between plate  
and SL-151 to allow for easy access in later steps. (See  
Figure 6)  
Figure 7  
WARNING: Exceeding the weight capacity can result in  
serious personal injury or damage to equipment! It is the  
installer’s responsibility to make sure the combined weight of  
all components located between the SMA-602 up to (and  
including) the projector does not exceed 105 lbs (47.6 kg).  
9
WARNING: Improper installation can result in serious  
personal injury or damage to equipment! The SL-151  
projector mount weighs in excess of 50 lbs! Use either a  
mechanical lifting device or at least two people to lift and  
install SL-151.  
4. Lift main plate and attached SL-151 underneath top slide  
plate making sure the four slots on each plate are  
perpendicular to each other. (See Figure 8)  
leave space  
5. Place bottom slide plate directly underneath main plate  
inserting four bolts through four slots in main plate.  
6. Insert four bolts up through four slots on top slide plate and  
secure using the four hex nuts removed in Step 1 of  
Disassemble Pipe Adapter Assembly. (See Figure 8)  
Figure 6  
6
 
Installation Instructions  
SMA-602  
Yaw Adjustment  
1. Loosen set screw on top slide plate pipe connector. (See  
Figure 10)  
removed hex nuts  
top slide plate  
2. Adjust YAW position until set screw faces target. (See  
Figure 10)  
bottom slide  
3. Tighten set screw on top slide plate pipe connector. (See  
Figure 10)  
plate (underneath)  
main plate  
5
6
2
Figure 10  
Figure 8  
Height Adjustment  
7. Lower hex nuts holding main plate in place to bring SL-151  
to desired height. (See Figure 8)  
1. Adjust hex nuts up or down in order to make sure the SL-  
151 is evenly mounted. (See Figure 11)  
Adjustments  
Location Adjustments  
1. Loosen four hex nuts holding plates together. (See Figure 9)  
2. Slide SL-151 in either direction until desired mounting  
location is reached. (See Figure 9)  
3. Tighten four hex nuts holding plates together. (See Figure  
9)  
1
2
2
Figure 11  
Projector Installation  
1. Refer to SL-151 Installation Manual for details on mounting  
projector to SL-151.  
Figure 9  
7
 
SMA-602  
Installation Instructions  
USA/International  
Europe  
A
P
F
A
P
F
6436 City West Parkway, Eden Prairie, MN 55344  
800.582.6480 / 952.225.6000  
877.894.6918 / 952.894.6918  
Franklinstraat 14, 6003 DK Weert, Netherlands  
+31 (0) 495 580 852  
+31 (0) 495 580 845  
Chief, a products division of  
Milestone AV Technologies  
Asia Pacific  
A
Office No. 1 on 12/F, Shatin Galleria  
18-24 Shan Mei Street  
Fotan, Shatin, Hong Kong  
852 2145 4099  
852 2145 4477  
8800-002540 Rev00  
¤2014 Milestone AV Technologies  
03/14  
P
F
 

Belkin Door W1896B 03 01 User Manual
BenQ Projector Accessories MX716 User Manual
Black Box Switch CATx User Manual
Black Decker Vacuum Cleaner CCV1000 User Manual
Bradford White Corp Water Heater 238 47808 00A User Manual
Braun Coffeemaker KF 140 AUTO OFF User Manual
Canon Camera Lens 0345B002 User Manual
Canon MP3 Docking Station DIM 521A User Manual
Castelle Fax Machine FaxPress User Manual
Chamberlain Garage Door Opener 182665D User Manual