Braun Iron 4 681 User Manual

SI 6575  
SI 6530  
SI 6245  
SI 6220  
SI 6210  
e s s  
p r  
t
a
t
s
o
m
r
e
h t  
/
f
f
o
-
o
t
u
a
m i n  
r
hi  
p
a
s
n
i
m
/
g
5
8
t
t
a
W
0
0
8
1
c
l
a
c
i
t
n
a
m a x  
m a x  
Type 4 681  
Type 4 694  
Type 4 699  
Braun Infoline  
Helpline  
GB  
Should you require any further  
assistance please call Braun (UK)  
Consumer Relations on  
08007837010  
Helpline  
IRL  
1800509448  
Helpline  
AUS  
Australian Consumer Service  
(free call):  
1800641820  
Internet:  
4-699-353/00/IV-02/G2  
UK/AUS  
Printed in Spain  
 
Our products are engineered to meet the  
highest standards of quality, functionality and  
design. We hope you enjoy your new Braun  
FreeStyle.  
D After ironing  
Unplug the iron and press the steam on/off  
button (3) so that it catches in its lower  
position (steam off).  
Notice: Remove the sole plate label, if any,  
before first use.  
To prolong the life of the iron, empty the  
water tank.  
–––––––––––––––––––––––––––––––––––––––––  
Important safeguards  
Store the cool iron in a dry place always  
standing on its heel rest.  
Before using the iron, read the use instruc-  
tions completely. Keep the use instructions  
during the entire life of the iron.  
Make sure your voltage corresponds to the  
voltage printed on the iron. Connect the  
iron to alternating current only.  
Always unplug the iron before filling with  
water and make sure the steam button is  
in its lower position (steam off). Always pull  
the plug, not the cord. The cord should  
never come in contact with hot objects or  
with the hot sole plate.  
E Maintenance and cleaning  
To clean the sole plate, use steel wool.  
Then wipe the sole plate clean with a cloth.  
Never use a scouring pad, vinegar nor  
other chemicals. To clean the soft material  
of handle and power shot and spray  
buttons, use soapy water.  
Never immerse the iron in water or other  
liquids.  
During ironing pauses, always place the  
iron upright on its heel rest. Unplug it when  
leaving the room, even if only for a short  
time.  
Never pull out the steam button (3) during  
ironing.  
Keep the iron away from children.  
Electric irons combine high temperatures  
and hot steam that could lead to burns.  
Check the cord regularly for possible  
damage.  
F Cleaning the anticalc valve  
The iron’s anticalc valve is located at the  
lower end of the steam button (3). It has  
to be decalcified regularly (e.g. when the  
steam development is insufficient).  
Proceed as follows:  
1) Unplug the iron and empty the water tank.  
2) Press the steam button so it is lifted.  
3) Remove carefully (some water may now  
leak from the sole plate).  
If the appliance (including cord) shows any  
defect, stop using it and take it to a Braun  
Service Centre for repair.  
Faulty or unqualified repair work may  
cause accidents or injury to the user.  
4) Do not touch the anit-calc valve.  
5) Immerse in vinegar (not vinegar essence)  
or lemon juice until the lime becomes soft.  
–––––––––––––––––––––––––––––––––––––––––  
6) Use a non-metallic brush until all openings  
are clean.  
A Description  
7) Rinse under running water.  
1
2
3
Spray nozzle  
Water tank opening  
Steam button  
8) Re-insert the steam button.  
3a Steam regulator  
9) Press to check the steam on/off function.  
4
5
6
7
Spray button  
Power shot button  
Note: the iron must never be used without  
the steam button.  
Temperature selector  
Temperature/auto-off* pilot light  
B Before starting off  
G Decalcifying/anticalc system  
This iron is designed for tap water. If you  
have extremely hard water, we recommend  
to use a mixture of 50% tap water and  
50% distilled water. Fill the water tank to  
«max» marking. Never use distilled water  
exclusively. Do not add any additives  
(e.g. starch).  
When scale particles come out of the  
steam vents or when the steam  
development is insufficient even after  
cleaning the anticalc valve, you should  
clean the steam chamber as follows:  
1) Make sure the steam button is in its lower  
position.  
Keep the iron in the upright position and  
connect it to the mains. Select the tem-  
perature according to the ironing guide on  
the heel rest of the iron or on the label in  
your garments.  
2)3) Fill water into the tank, connect to the  
mains and select the «•••» temperature  
setting.  
The temperature pilot light (7) goes off,  
when the desired temperature is reached  
(after approx. 1 minute).  
4)5) Wait until the pilot light turns off.  
Unplug the iron.  
6)7) Hold the iron over a sink, then press the  
steam button so it is lifted, carefully pull it  
up, turn it and rest it in this position.  
C Ironing  
1 Steam on/off  
Caution: When the steam button is pulled  
up, hot water and steam will come out from  
the sole plate.  
For steam ironing, the temperature selector  
(6) must be set within the red range.  
Press the steam button (3) to start the  
steam mode.  
8) Push back the steam button until it catches  
in the lower position.  
p r e s s  
e s s  
p r  
9)10) Fill water into the tank, connect to the  
mains and select the «•••» temperature  
setting.  
steam on  
steam off  
11)13) When the pilot light goes off, press  
the power shot button 4 times to rinse the  
iron. Disconnect the iron and wait for the  
sole plate to cool off, then clean it as  
described above in section E.  
With the steam button in its upper position,  
turn the steam regulator (3a) to adjust the  
steam quantity.  
Preconditioning  
(not with SI 6210 model)  
Note: the iron must never be used without  
the steam button.  
Steam develops also horizontally at the  
front area of the sole plate. This pre-  
conditions the textiles by «pre-steaming»,  
thus making ironing easier.  
Be careful – steam comes out laterally.  
H Trouble-shooting guide  
2 Power shot  
Prior to use, press the power shot button  
(5) 3 to 4 times to activate it. Press the  
power shot button in intervals of at least  
5 seconds.  
Problem  
Remedy  
––––––––––––––––––––––––––––––––––––––  
Drops  
Turn the steam regulator  
anti-clockwise to reduce  
the steam or press the  
steam button to turn the  
steam off.  
Power shot can be activated when dry  
ironing. However, the temperature selector  
has to be set in the range between «•••»  
and «max». The power shot function can  
also be used in the vertical position for  
steaming hanging clothes.  
coming out  
of the steam  
vents  
Take longer intervals  
when pressing the power  
shot button.  
Select a higher tempera-  
ture setting.  
3 Spray function  
Press the spray button (4).  
No steam  
at all  
Press the steam button  
so that it is lifted.  
4 Dry ironing  
Turn the steam mode off by pressing the  
steam button (3) so that it catches in the  
lower position.  
Less steam  
develops or no (see F).  
steam at all  
Clean the anticalc valve  
5 Automatic shut-off*  
(*available on SI 6245 model only)  
Important: the auto shut-off feature is  
mercury-free. The auto shut-off mechanism  
causes a slight rattling noise during ironing.  
This is normal and in no case indicates a  
fault of the iron. The «auto-off» pilot light (7)  
will flash when the automatic shut-off is  
activated. This happens when the iron has  
rested:  
Calcium  
Decalcify the steam  
chamber (see G).  
particles  
coming through  
the steam vents  
––––––––––––––––––––––––––––––––––––––  
– horizontally on the soleplate for about  
30 seconds or  
Subject to change without notice.  
– vertically on the heel rest (8) for about  
15 minutes or  
– when the iron has been lying on its side  
for about 30 seconds.  
To turn on the iron again just move it.  
When the «auto-off» pilot light (7) stops  
flashing the electrical power is on again.  
This product conforms to the  
EMC-Requirements as laid down  
by the Council Directive 89/336/EEC  
and to the Low Voltage Regulation  
(73/23 EEC).  
 
For UK only:  
Guarantee  
We grant 2 years guarantee on the product  
commencing on the date of purchase. Within  
the guarantee period we will eliminate, free of  
charge, any defects in the appliance resulting  
from faults in materials or workmanship, either  
by repairing or replacing the complete ap-  
pliance as we may choose.  
This guarantee extends to every country where  
this appliance is supplied by Braun or its ap-  
pointed distributor.  
This guarantee does not cover: damage due  
to improper use, normal wear or use as well  
as defects that have a negligible effect on  
the value or operation of the appliance. The  
guarantee becomes void if repairs are under-  
taken by unauthorised persons and if original  
Braun parts are not used.  
To obtain service within the guarantee period,  
hand in or send the complete appliance with  
your sales receipt to an authorised Braun  
Customer Service Centre.  
This guarantee in no way affects your rights  
under statutory law.  
 

BellSouth Scanner S02294A User Manual
Belson Fan WSF1610 User Manual
Black Decker Trimmer LHT2220B User Manual
Boston Acoustics Stereo Amplifier GT 2125 User Manual
Braun Juicer 4161 User Manual
Brother Fax Machine DCP7010 User Manual
Canon Camera Lens 1242B002 User Manual
Canon CRT Television KV 2199XDK User Manual
Casio Digital Camera EX FC150 User Manual
Casio Electronic Keyboard AP 400 User Manual